在鄭州區域為什么推薦隔墻板(內含英文翻譯)
輕質隔墻板的制造工藝，決定了良好的隔熱保溫功能，讓您的室內環境更加舒適。在鄭州區域為什么推薦隔墻板(內含英文翻譯)
施工要點：1、檢查隔墻板的幾何尺寸，以符合標準要求為準。2、根據排圖，預先40×50×90L型鐵件固定在應固定的部位。3、按排圖，從一側開始安裝。若隔墻板上有門窗洞口，就從門窗洞口向兩側開始安裝。對準墨線，用撬棍盡力在底部撬動，上端頂緊，板邊嚴實，底部用木楔塞牢，加上加固件。4、安裝時，隨時檢查平整度、垂直度等有關檢查的項目。5、水電埋管鋪設應與隔墻板安裝同步進行，隔墻板面需要開口時，應在安裝前鉆孔，洞口不得大于80mm×80mm；水暖吊掛件不能超過80公斤，超過80公斤的吊掛件，必須安裝在隔墻板的固定預埋件上。6、電器接線開關、插座等四周，應用充填料抹平。7、隔墻板安裝后，粘接材料必須干燥，才能進行下道工序，正常需要安裝之日起10-15天方能進行裝飾。8、安裝好的隔墻板面不得起皮、掉角、空鼓和裂縫，按每面墻的平面計算，達到建筑中級抹灰。
輕質隔墻板是一種新型節能墻材料，它是一種外型像空心樓板一樣的墻材，但是它兩邊有公母榫槽，安裝時只需將板材立起，公、母隼涂上少量嵌縫砂漿后對拼裝起來即可。它是由無害化磷石膏、輕質鋼渣、粉煤灰等多種工業廢渣組成，經變頻蒸汽加壓養護而成。輕質隔墻板具有質量輕、強度高、多重環保、保溫隔熱、隔音、呼吸調濕、防火、快速施工、降低墻體成本等優點。內層裝有合理布局的隔熱、吸聲的無機發泡型材或其他保溫材料，墻板經流水線澆注、整平、科學養護而成，生產自動化程度高，規格品種多。
關于更多輕質隔墻板相關資料聯系：15515532955（微信同號）
The manufacturing process of light partition board determines the good heat insulation function, making your indoor environment more comfortable.
Key points of Construction: 1. Check the geometric dimension of partition board to meet the standard requirements. 2. According to the layout, 40 in advance × fifty × 90L type iron parts are fixed at the parts that should be fixed. 3. Install from one side according to the layout. If there are door and window openings on the partition board, install from the door and window openings to both sides. Align the ink line, use a crowbar to pry at the bottom as much as possible, tighten the upper end, keep the board edge tight, plug the bottom with a wooden wedge, and add reinforcement. 4. During installation, check the flatness, verticality and other related inspection items at any time. 5. The laying of buried water and electricity pipes should be carried out synchronously with the installation of partition board. When the partition board needs to be opened, it should be drilled before installation, and the opening should not be greater than 80mm × 80mm； Plumbing hangers shall not exceed 80 kg. Hangers exceeding 80 kg must be installed on fixed embedded parts of partition board. 6. The surrounding of electrical wiring switches and sockets shall be smoothed with fillers. 7. After the partition board is installed, the bonding material must be dry before the next process can be carried out. The decoration can be carried out 10-15 days from the date of normal installation. 8. The installed partition board shall be free of peeling, corner falling, hollowing and cracks. It shall be calculated according to the plane of each wall to achieve building intermediate plastering.
Light partition board is a new type of energy-saving wall material. It is a kind of wall material with the same appearance as hollow floor slab, but it has male and female mortise grooves on both sides. When installing, you only need to erect the board, and the male and female falcons can be assembled after being coated with a small amount of caulking mortar. It is composed of harmless phosphogypsum, light steel slag, fly ash and other industrial waste residues, which are cured by variable-frequency steam pressure. Light partition board has the advantages of light weight, high strength, multiple environmental protection, thermal insulation, sound insulation, respiratory humidity regulation, fire prevention, rapid construction, reducing wall cost and so on. The inner layer is equipped with reasonably arranged insulating and sound-absorbing inorganic foaming profiles or other insulation materials. The wallboard is poured, leveled and scientifically maintained by the assembly line. The production automation is high, and there are many specifications and varieties.
For more information about lightweight partition board, contact: 15515532955 (wechat same number)
